|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
LTC2205-14 14-Bit, 65Msps ADC FEATURES DESCRIPTIO Sample Rate: 65Msps 78.3dB SNR and 98dB SFDR (2.25VP-P Range) SFDR >90dB at 140MHz (1.5VP-P Input Range) PGA Front End (2.25VP-P or 1.5VP-P Input Range) 700MHz Full Power Bandwidth S/H Optional Internal Dither Optional Data Output Randomizer Single 3.3V Supply Power Dissipation: 600mW Optional Clock Duty Cycle Stabilizer Out-of-Range Indicator Pin Compatible Family 105Msps: LTC2207 (16-Bit), LTC2207-14 (14-Bit) 80Msps: LTC2206 (16-Bit), LTC2206-14 (14-Bit) 65Msps: LTC2205 (16-Bit) 40Msps: LTC2204 (16-Bit) 48-Pin (7mm x 7mm) QFN Package The LTC(R)2205-14 is a sampling 14-bit A/D converter designed for digitizing high frequency, wide dynamic range signals up to input frequencies of 700MHz. The input range of the ADC can be optimized with the PGA front end. The LTC2205-14 is perfect for demanding communications applications, with AC performance that includes 78.3dB SNR and 98dB spurious free dynamic range (SFDR). Ultralow jitter of 90fsRMS allows undersampling of high input frequencies with excellent noise performance. Maximum DC specs include 1.5LSB INL, 1LSB DNL (no missing codes). A separate output power supply allows the CMOS output swing to range from 0.5V to 3.6V. The ENC+ and ENC- inputs may be driven differentially or single-ended with a sine wave, PECL, LVDS, TTL or CMOS inputs. An optional clock duty cycle stabilizer allows high performance at full speed with a wide range of clock duty cycles. , LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. APPLICATIO S Telecommunications Receivers Cellular Base Stations Spectrum Analysis Imaging Systems ATE TYPICAL APPLICATIO 3.3V SENSE VCM 2.2F AIN+ ANALOG INPUT AIN- 1.25V COMMON MODE BIAS VOLTAGE INTERNAL ADC REFERENCE GENERATOR OVDD 0.5V TO 3.6V 0.1F OF CLKOUT D13 * * * D0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 S/H AMP - 14-BIT PIPELINED ADC CORE CORRECTION LOGIC AND SHIFT REGISTER OUTPUT DRIVERS OGND CLOCK/DUTY CYCLE CONTROL VDD 0.1F GND ENC ENC PGA SHDN DITH MODE OE RAND 0.1F 220514 TA01 3.3V 0.1F AMPLITUDE (dBFS) + ADC CONTROL INPUTS U LTC2205-14: 32K Point FFT, fIN = 5.1MHz, -1dBFS, PGA = 0, DITH = 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G04 U U 220514fa 1 LTC2205-14 ABSOLUTE MAXIMUM RATINGS OVDD = VDD (Notes 1 and 2) PACKAGE/ORDER INFORMATION 48 GND 47 PGA 46 RAND 45 MODE 44 OE 43 OF 42 D13 41 D12 40 D11 39 D10 38 OGND 37 OVDD SENSE 1 VCM 2 VDD 3 VDD 4 GND 5 AIN+ 6 AIN- 7 GND 8 ENC+ 9 ENC- 10 GND 11 VDD 12 49 36 OVDD 35 D9 34 D8 33 D7 32 D6 31 OGND 30 CLKOUT+ 29 CLKOUT- 28 D5 27 D4 26 D3 25 OVDD UK PACKAGE 48-LEAD (7mm x 7mm) PLASTIC QFN TJMAX = 125C, JA = 29C/W EXPOSED PAD IS GND (PIN 49), MUST BE SOLDERED TO PCB BOARD TOP VIEW Supply Voltage (VDD) ................................... -0.3V to 4V Digital Output Ground Voltage (OGND)........ -0.3V to 1V Analog Input Voltage (Note 3) ......-0.3V to (VDD + 0.3V) Digital Input Voltage .....................-0.3V to (VDD + 0.3V) Digital Output Voltage ................ -0.3V to (OVDD + 0.3V) Power Dissipation............................................ 2000mW Operating Temperature Range LTC2205-14C ........................................... 0C to 70C LTC2205-14I ........................................ -40C to 85C Storage Temperature Range .................. -65C to 150C Digital Output Supply Voltage (OVDD) .......... -0.3V to 4V ORDER PART NUMBER LTC2205CUK-14 LTC2205IUK-14 Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF Lead Free Part Marking: http://www.linear.com/leadfree/ Consult LTC Marketing for parts specified with wider operating temperature ranges. CONVERTER CHARACTERISTICS PARAMETER Resolution (No Missing Codes) Integral Linearity Error Differential Linearity Error Offset Error Offset Drift Gain Error Full-Scale Drift Transition Noise The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4) CONDITIONS VDD 13 VDD 14 GND 15 SHDN 16 DITH 17 NC 18 NC 19 D0 20 D1 21 D2 22 OGND 23 OVDD 24 UK PART MARKING LTC2205UK-14 LTC2205UK-14 MIN 14 TYP 0.6 0.2 1 10 0.3 30 10 0.7 MAX 1.5 1 8.5 1.9 UNITS Bits LSB LSB mV V/C %FS ppm/C ppm/C Differential Analog Input (Note 5) Differential Analog Input (Note 6) External Reference Internal Reference External Reference LSBRMS 220514fa 2 LTC2205-14 The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4) SYMBOL VIN VIN, CM IIN ISENSE IMODE CIN tAP tJITTER CMRR BW-3dB PARAMETER Analog Input Range (AIN+ - AIN-) Analog Input Common Mode Analog Input Leakage Current SENSE Input Leakage Current MODE Pin Pull-Down Current to GND Analog Input Capacitance Sample-and-Hold Aperature Delay Time Sample-and-Hold Aperature Delay Time Jitter Analog Input Common Mode Rejection Ratio Full Power Bandwidth CONDITIONS 3.135V VDD 3.465V Differential Input (Note 7) 0V AIN+, AIN- VDD 0V SENSE VDD Sample Mode ENC+ < ENC- Hold Mode ENC+ > ENC- MIN ANALOG INPUT 1 -1 -3 TYP 1.5 to 2.25 1.25 MAX 1.5 1 3 10 6.5 1.8 0.7 90 UNITS VP-P V A A A pF pF ns fsRMS dB MHz 1V < (AIN+ = AIN-) <1.5V 60 700 DYNAMIC ACCURACY SYMBOL PARAMETER SNR Signal-to-Noise Ratio The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. AIN = -1dBFS. (Note 4) CONDITIONS 5MHz Input (2.25V Range, PGA = 0) 5MHz Input (1.5V Range, PGA = 1) 15MHz Input (2.25V Range, PGA = 0) 15MHz Input (2.25V Range, PGA = 0) 15MHz Input (1.5V Range, PGA = 1) 70MHz Input (2.25V Range, PGA = 0) 70MHz Input (1.5V Range, PGA = 1) 70MHz Input (1.5V Range, PGA = 1) 140MHz Input (2.25V Range, PGA = 0) 140MHz Input (1.5V Range, PGA = 1) 170MHz Input (2.25V Range, PGA = 0) 170MHz Input (1.5V Range, PGA = 1) SFDR Spurious Free Dynamic Range 2nd or 3rd Harmonic 5MHz Input (2.25V Range, PGA = 0) 5MHz Input (1.5V Range, PGA = 1) 15MHz Input (2.25V Range, PGA = 0) 15MHz Input (2.25V Range, PGA = 0 15MHz Input (1.5V Range, PGA = 1) 70MHz Input (2.25V Range, PGA = 0) 70MHz Input (1.5V Range, PGA = 1) 70MHz Input (1.5V Range, PGA = 1) 140MHz Input (2.25V Range, PGA = 0) 140MHz Input (1.5V Range, PGA = 1) 170MHz Input (2.25V Range, PGA = 0) 170MHz Input (1.5V Range, PGA = 1) MIN TYP 78.3 76.0 MAX UNITS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc 76.8 77.2 78.2 78.2 76.0 77.7 75.7 76.4 74.9 75.6 74.2 98 98 74.2 74.7 85 86 98 98 98 90 92 92 88 90 80 82 82 83 220514fa 3 LTC2205-14 DYNAMIC ACCURACY SYMBOL PARAMETER SFDR Spurious Free Dynamic Range 4th Harmonic or Higher The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. AIN = -1dBFS unless otherwise noted. (Note 4) CONDITIONS 5MHz Input (2.25V Range, PGA = 0) 5MHz Input (1.5V Range, PGA = 1) 15MHz Input (2.25V Range, PGA = 0) 15MHz Input (1.5V Range, PGA = 1) 70MHz Input (2.25V Range, PGA = 0) 70MHz Input (1.5V Range, PGA = 1) 140MHz Input (2.25V Range, PGA = 0) 140MHz Input (1.5V Range, PGA = 1) 170MHz Input (2.25V Range, PGA = 0) 170MHz Input (1.5V Range, PGA = 1) MIN TYP 103 103 MAX UNITS dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS 87 98 98 98 98 95 95 93 93 78.2 75.9 86.5 S/(N+D) Signal-to-Noise Plus Distortion Ratio 5MHz Input (2.25V Range, PGA = 0) 5MHz Input (1.5V Range, PGA = 1) 15MHz Input (2.25V Range, PGA = 0) 15MHz Input (2.25V Range, PGA = 0) 15MHz Input (1.5V Range, PGA = 1) 70MHz Input (2.25V Range, PGA = 0) 70MHz Input (1.5V Range, PGA = 1) 70MHz Input (1.5V Range, PGA = 1) 140MHz Input (2.25V Range, PGA = 0) 140MHz Input (1.5V Range, PGA = 1) 170MHz Input (2.25V Range, PGA = 0) 170MHz Input (1.5V Range, PGA = 1) 76.7 77.1 78.1 78.1 75.9 77.4 75.5 75.5 75.9 74.7 73.6 73.2 103 103 103 103 103 103 98 98 98 98 113 113 73.5 74.0 SFDR Spurious Free Dynamic Range at -25dBFS Dither "OFF" 5MHz Input (2.25V Range, PGA = 0) 5MHz Input (1.5V Range, PGA = 1) 15MHz Input (2.25V Range, PGA = 0) 15MHz Input (1.5V Range, PGA = 1) 70MHz Input (2.25V Range, PGA = 0) 70MHz Input (1.5V Range, PGA = 1) 140MHz Input (2.25V Range, PGA = 0) 140MHz Input (1.5V Range, PGA = 1) 170MHz Input (2.25V Range, PGA = 0) 170MHz Input (1.5V Range, PGA = 1) SFDR Spurious Free Dynamic Range at -25dBFS Dither "ON" 5MHz Input (2.25V Range, PGA = 0) 5MHz Input (1.5V Range, PGA = 1) 15MHz Input (2.25V Range, PGA = 0) 15MHz Input (1.5V Range, PGA = 1) 70MHz Input (2.25V Range, PGA = 0) 70MHz Input (1.5V Range, PGA = 1) 140MHz Input (2.25V Range, PGA = 0) 140MHz Input (1.5V Range, PGA = 1) 170MHz Input (2.25V Range, PGA = 0) 170MHz Input (1.5V Range, PGA = 1) 95 113 113 110 110 110 110 103 103 220514fa 4 LTC2205-14 COMMON MODE BIAS CHARACTERISTICS PARAMETER VCM Output Voltage VCM Output Tempco VCM Line Regulation VCM Output Resistance CONDITIONS IOUT = 0 IOUT = 0 3.135V VDD 3.465V 1mA | IOUT | 1mA The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4) MIN 1.15 TYP 1.25 40 1 1 MAX 1.35 UNITS V ppm/C mV/ V DIGITAL INPUTS AND DIGITAL OUTPUTS SYMBOL PARAMETER ENCODE INPUTS (ENC+, ENC-) VID Differential Input Voltage (Note 7) VICM Common Mode Input Voltage RIN Input Resistance CIN Input Capacitance LOGIC INPUTS (DITH, PGA, SHDN, RAND) VIH High Level Input Voltage VIL Low Level Input Voltage IIN Digital Input Current CIN Digital Input Capacitance LOGIC OUTPUTS OVDD = 3.3V VOH High Level Output Voltage VOL ISOURCE ISINK OVDD = 2.5V VOH VOL OVDD = 1.8V VOH VOL Low Level Output Voltage Output Source Current Output Sink Current High Level Output Voltage Low Level Output Voltage High Level Output Voltage Low Level Output Voltage CONDITIONS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4) MIN TYP MAX UNITS V 0.2 1.6 1.2 6 3 3.0 Internally Set Externally Set (Note 7) (See Figure 2) (Note 7) VDD = 3.3V VDD = 3.3V VIN = 0V to VDD (Note 7) V V k pF V V A pF 2 0.8 10 1.5 VDD = 3.3V VDD = 3.3V VOUT = 0V VOUT = 3.3V VDD = 3.3V VDD = 3.3V VDD = 3.3V VDD = 3.3V IO = -10A IO = -200A IO = 160A IO = 1.6mA 3.1 3.299 3.29 0.01 0.10 -50 50 2.49 0.1 1.79 0.1 0.4 V V V V mA mA V V V V IO = -200A IO = 1.60mA IO = -200A IO = 1.60mA POWER REQUIREMENTS SYMBOL VDD PSHDN OVDD IVDD PDIS PARAMETER Analog Supply Voltage Shutdown Power Output Supply Voltage Analog Supply Current Power Dissipation The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4) CONDITIONS SHDN = VDD MIN 3.315 0.5 TYP 3.3 0.2 3.3 181 597 MAX 3.465 3.6 212 700 UNITS V mW V mA mW 220514fa 5 LTC2205-14 TIMING CHARACTERISTICS SYMBOL fS tL tH tAP tD tC tSKEW tOE Pipeline Latency Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All voltage values are with respect to GND, with GND and OGND shorted (unless otherwise noted). Note 3: When these pin voltages are taken below GND or above VDD, they will be clamped by internal diodes. This product can handle input currents of greater than 100mA below GND or above VDD without latchup. Note 4: VDD = 3.3V, fSAMPLE = 65MHz differential ENC+/ENC- = 2VP-P sine wave with 1.6V common mode, input range = 2.25VP-P with differential drive (PGA = 0), unless otherwise specified. PARAMETER Sampling Frequency ENC Low Time ENC High Time Sample-and-Hold Aperture Delay ENC to DATA Delay ENC to CLKOUT Delay DATA to CLKOUT Skew DATA Access Time Bus Relinquish Time (Note 7) (Note 7) (tD - tC) (Note 7) CL = 5pf (Note 7) (Note 7) The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4) CONDITIONS MIN 1 6.40 4.60 6.40 4.60 7.69 7.69 7.69 7.69 0.7 1.3 1.3 -0.6 2.7 2.7 0 5 5 7 MAX 65 500 500 500 500 UNITS MHz ns ns ns ns ns Duty Cycle Stabilizer Off (Note 7) Duty Cycle Stabilizer On (Note 7) Duty Cycle Stabilizer Off (Note 7) Duty Cycle Stabilizer On (Note 7) 4.0 4.0 0.6 15 15 ns ns ns ns ns Cycles Note 5: Integral nonlinearity is defined as the deviation of a code from a "best fit straight line" to the transfer curve. The deviation is measured from the center of the quantization band. Note 6: Offset error is the offset voltage measured from -1/2LSB when the output code flickers between 00 0000 0000 0000 and 11 1111 1111 1111 in 2's complement output mode. Note 7: Guaranteed by design, not subject to test. 220514fa 6 LTC2205-14 TYPICAL PERFORMANCE CHARACTERISTICS LTC2205-14: INL (Integral Nonlinearity) vs Code 1.5 1.0 0.5 DNL (LSB) INL (LSB) 0.25 0 COUNT 150,000 0 -0.5 -1.0 -0.75 -1.5 0 4096 8192 CODE 12288 16384 220514 G01 LTC2205-14: DNL (Differential Nonlinearity) vs Code 1.00 0.75 200,000 0.50 250,000 LTC2205-14: Grounded Input Histogram -0.25 -0.50 100,000 50,000 -1.00 0 0 4096 8192 CODE 220514 G02 12288 16384 8175 8176 8177 8178 CODE 8179 8180 220514 G03 LTC2205-14: 32K Point FFT, -1dBFS, fIN = 5.1MHz, PGA = 0, DITH = 0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G04 LTC2205-14: 32K Point FFT, -1dBFS, fIN = 5.1MHz, PGA = 1, DITH = 0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G05 LTC2205-14: 32K Point FFT, -25dBFS, fIN = 5.1MHz, PGA = 0, DITH = 0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G06 AMPLITUDE (dBFS) AMPLITUDE (dBFS) LTC2205-14: 32K Point FFT, -25dBFS, fIN = 5.1MHz, PGA = 0, DITH = 1 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G07 LTC2205-14: 32K Point FFT, -40dBFS, fIN = 5.1MHz, PGA = 0, DITH = 0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G08 AMPLITUDE (dBFS) AMPLITUDE (dBFS) LTC2205-14: 32K Point FFT, -40dBFS, fIN = 5.1MHz, PGA = 0, DITH = 1 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G09 AMPLITUDE (dBFS) AMPLITUDE (dBFS) 220514fa 7 LTC2205-14 TYPICAL PERFORMANCE CHARACTERISTICS LTC2205-14: 32K Point FFT, -1dBFS, fIN = 15.1MHz, PGA = 0, DITH = 0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G10 LTC2205-14: 32K Point FFT, -1dBFS, fIN = 15.1MHz, PGA = 1, DITH = 0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G11 LTC2205-14: 32K Point FFT, -25dBFS, fIN = 15.1MHz, PGA = 0, DITH = 0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G12 AMPLITUDE (dBFS) AMPLITUDE (dBFS) LTC2205-14: 32K Point FFT, -25dBFS, fIN = 15.1MHz, PGA = 0, DITH = 1 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G13 LTC2205-14: 32K Point FFT, -40dBFS, fIN = 15.1MHz, PGA = 0, DITH = 0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G14 AMPLITUDE (dBFS) LTC2205-14: 32K Point FFT, -40dBFS, fIN = 15.1MHz, PGA = 0, DITH = 1 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G15 AMPLITUDE (dBFS) AMPLITUDE (dBFS) LTC2205-14: 32K Point FFT, -1dBFS, fIN = 70.1MHz, PGA = 0, DITH = 0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G16 LTC2205-14: 32K Point FFT, -25dBFS, fIN = 70.1MHz, PGA = 1, DITH = 0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G17 AMPLITUDE (dBFS) AMPLITUDE (dBFS) LTC2205-14: 32K Point FFT, -25dBFS, fIN = 70.1MHz, PGA = 0, DITH = 1 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G19 AMPLITUDE (dBFS) AMPLITUDE (dBFS) 220514fa 8 LTC2205-14 TYPICAL PERFORMANCE CHARACTERISTICS LTC2205-14: 32K Point FFT, -40dBFS, fIN = 70.1MHz, PGA = 0, DITH = 0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 15 10 20 25 FREQUENCY (MHz) 30 220514 G20 LTC2205-14: 32K Point FFT, -40dBFS, fIN = 70.1MHz, PGA = 0, DITH = 1 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G21 LTC2205-14: 32K Point FFT, -1dBFS, fIN = 140.1MHz, PGA = 0, DITH = 0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G22 AMPLITUDE (dBFS) LTC2205-14: 32K Point FFT, -1dBFS, fIN = 140.1MHz, PGA = 1, DITH = 0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G23 AMPLITUDE (dBFS) LTC2205-14: 32K Point FFT, -25dBFS, fIN = 140.1MHz, PGA = 0, DITH = 0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G24 AMPLITUDE (dBFS) AMPLITUDE (dBFS) LTC2205-14: 32K Point FFT, -25dBFS, fIN = 140.1MHz, PGA = 0, DITH = 1 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G25 AMPLITUDE (dBFS) LTC2205-14: 32K Point FFT, -40dBFS, fIN = 140.1MHz, PGA = 0, DITH = 0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G26 AMPLITUDE (dBFS) LTC2205-14: 32K Point FFT, -40dBFS, fIN = 140.1MHz, PGA = 0, DITH = 1 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G27 LTC2205-14: 32K Point FFT, fIN1 = 14.9MHz, -7dBFS, fIN2 = 20.1MHz, -7dBFS, PGA = 0, DITH = 1 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 10 20 25 15 FREQUENCY (MHz) 30 220514 G28 AMPLITUDE (dBFS) AMPLITUDE (dBFS) AMPLITUDE (dBFS) 220514fa 9 LTC2205-14 TYPICAL PERFORMANCE CHARACTERISTICS LTC2205-14: 32K Point FFT, fIN1 = 64.1MHz, -7dBFS, fIN2 = 70.1MHz, -7dBFS, PGA = 0, DITH = 0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 5 15 10 20 25 FREQUENCY (MHz) 30 220514 G29 LTC2205-14: SFDR vs Input Level, fIN = 5.1MHz, RAND = 1, DITH = 0 120 110 100 SFDR (dBFS AND dBc) SFDR (dBFS AND dBc) 90 80 70 60 50 40 30 20 -80 -70 -60 -50 -40 -30 -20 -10 INPUT LEVEL (dBFS) 0 120 110 100 90 80 70 60 50 40 30 LTC2205-14: SFDR vs Input Level, fIN = 5.1MHz, RAND = 1, DITH = 1 AMPLITUDE (dBFS) 20 -80 -70 -60 -50 -40 -30 -20 -10 INPUT LEVEL (dBFS) 0 220514 G30 220514 G31 LTC2205-14: SFDR vs Input Level, fIN = 14.9MHz, RAND = 1, DITH = 0 120 110 100 SFDR (dBFS AND dBc) SFDR (dBFS AND dBc) 90 80 70 60 50 40 30 20 -80 -70 -60 -50 -40 -30 -20 -10 INPUT LEVEL (dBFS) 0 120 110 100 90 80 70 60 50 40 30 LTC2205-14: SFDR vs Input Level, fIN = 14.9MHz, RAND = 1, DITH = 1 120 110 100 SFDR (dBFS AND dBc) 0 90 80 70 60 50 40 30 LTC2205-14: SFDR vs Input Level, fIN = 70.1MHz, RAND = 1, DITH = 0 20 -80 -70 -60 -50 -40 -30 -20 -10 INPUT LEVEL (dBFS) 20 -80 -70 -60 -50 -40 -30 -20 -10 INPUT LEVEL (dBFS) 0 220514 G32 220514 G33 220514 G34 LTC2205-14: SFDR vs Input Level, fIN = 70.9MHz, RAND = 1, DITH = 1 120 110 100 SFDR (dBFS AND dBc) SFDR (dBFS AND dBc) 90 80 70 60 50 40 30 20 -80 -70 -60 -50 -40 -30 -20 -10 INPUT LEVEL (dBFS) 0 120 110 100 90 80 70 60 50 40 30 LTC2205-14: SFDR vs Input Level, fIN = 140.1MHz, RAND = 1, DITH = 0 120 110 100 SFDR (dBFS AND dBc) 0 90 80 70 60 50 40 30 LTC2205-14: SFDR vs Input Level, fIN = 140.1MHz, RAND = 1, DITH = 1 20 -80 -70 -60 -50 -40 -30 -20 -10 INPUT LEVEL (dBFS) 20 -80 -70 -60 -50 -40 -30 -20 -10 INPUT LEVEL (dBFS) 0 220514 G35 220514 G36 220514 G37 220514fa 10 LTC2205-14 TYPICAL PERFORMANCE CHARACTERISTICS LTC2205-14: SFDR vs Input Frequency, RAND = 1, DITH = 1 110 79 78 100 SNR (dBFS) SFDR (dBc) PGA = 1 90 PGA = 0 80 74 70 73 0 50 150 200 100 INPUT FREQUENCY (MHz) 250 220414 G38 LTC2205-14: SNR vs Input Frequency, RAND = 1, DITH = 0 110 LTC2205-14: SFDR and SNR vs Sample Rate, fIN = 5.1MHz, RAND = 0, DITH = 0 SFDR (dBc) AND SNR (dBFS) SFDR 100 77 PGA = 0 76 75 90 PGA = 1 80 SNR 70 0 50 100 150 200 INPUT FREQUENCY (MHz) 250 220514 G39 0 10 20 30 40 50 60 70 80 90 100 SAMPLE RATE (Msps) 220514 G40 LTC2205-14: SFDR and SNR vs Supply Voltage, fIN = 5.1MHz, RAND = 0, DITH = 0 110 SFDR 100 IVDD (mA) 220 210 SFDR (dBc) AND SNR (dBFS) 200 190 180 170 160 80 SNR 70 2.4 2.6 2.8 3.0 3.2 SUPPLY VOLTAGE (V) 3.4 3.6 150 140 130 90 LTC2205-14: IVDD vs Sample Rate, fIN = 5.1MHz, RAND = 0, DITH = 0 0.05 VDD = 3.47V GAIN DRIFT (% FS) VDD = 3.3V 0 -0.05 -0.10 -0.15 -0.20 -0.25 -0.30 0 10 20 30 40 50 60 70 80 90 100 100 SAMPLE RATE (Msps) 220214 G42 LTC2205-14: Gain Drift with Internal Reference vs Temperature VDD = 3.13V -0.35 20 40 60 -60 -40 -20 0 TEMPERATURE (C) 80 100 220514 G41 220514 G43 220514fa 11 LTC2205-14 PIN FUNCTIONS SENSE (Pin 1): Reference Mode Select and External Reference Input. Tie SENSE to VDD to select the internal 2.5V bandgap reference. An external reference of 2.5V or 1.25V may be used; both reference values will set a full scale ADC range of 2.25V (PGA = 0). VCM (Pin 2): 1.25V Output. Optimum voltage for input common mode. Must be bypassed to ground with a minimum of 2.2F. Ceramic chip capacitors are recommended. VDD (Pins 3, 4, 12, 13, 14): 3.3V Analog Supply Pin. Bypass to GND with 0.1F ceramic chip capacitors. GND (Pins 5, 8, 11, 15, 48): ADC Power Ground. AIN+ (Pin 6): Positive Differential Analog Input. AIN- (Pin 7): Negative Differential Analog Input. ENC+ (Pin 9): Positive Differential Encode Input. The sampled analog input is held on the rising edge of ENC+. Internally biased to 1.6V through a 6.2k resistor. Output data can be latched on the rising edge of ENC+. ENC- (Pin 10): Negative Differential Encode Input. The sampled analog input is held on the falling edge of ENC-. Internally biased to 1.6V through a 6.2k resistor. Bypass to ground with a 0.1F capacitor for a single-ended Encode signal. SHDN (Pin 16): Power Shutdown Pin. SHDN = low results in normal operation. SHDN = high results in powered down analog circuitry and the digital outputs placed in a high impedance state. DITH (Pin 17): Internal Dither Enable Pin. DITH = low disables internal dither. DITH = high enables internal dither. Refer to Internal Dither section of this data sheet for details on dither operation. NC (Pins 18, 19): No Connect. D0-D13 (Pins 20-22, 26-28, 32-35 and 39-42): Digital Outputs. D13 is the MSB. OGND (Pins 23, 31 and 38): Output Driver Ground. OVDD (Pins 24, 25, 36, 37): Positive Supply for the Output Drivers. Bypass to ground with 0.1F ceramic chip capacitors. CLKOUT- (Pin 29): Data Valid Output. CLKOUT- will toggle at the sample rate. Latch the data on the falling edge of CLKOUT-. CLKOUT+ (Pin 30): Inverted Data Valid Output. CLKOUT+ will toggle at the sample rate. Latch the data on the rising edge of CLKOUT+. OF (Pin 43): Over/Under Flow Digital Output. OF is high when an over or under flow has occurred. (Pin 44): Output Enable Pin. Low enables the digital O E output drivers. High puts digital outputs in Hi-Z state. MODE (Pin 45): Output Format and Clock Duty Cycle Stabilizer Selection Pin. Connecting MODE to 0V selects offset binary output format and disables the clock duty cycle stabilizer. Connecting MODE to 1/3VDD selects offset binary output format and enables the clock duty cycle stabilizer. Connecting MODE to 2/3VDD selects 2's complement output format and enables the clock duty cycle stabilizer. Connecting MODE to VDD selects 2's complement output format and disables the clock duty cycle stabilizer. RAND (Pin 46): Digital Output Randomization Selection Pin. RAND low results in normal operation. RAND high selects D1-D13 to be EXCLUSIVE-ORed with D0 (the LSB). The output can be decoded by again applying an XOR operation between the LSB and all other bits. This mode of operation reduces the effects of digital output interferance. PGA (Pin 47): Programmable Gain Amplifier Control Pin. Low selects a front-end gain of 1, input range of 2.25VP-P. High selects a front-end gain of 1.5, input range of 1.5VP-P. GND (Exposed Pad, Pin 49): ADC Power Ground. The exposed pad on the bottom of the package must be soldered to ground. 220514fa 12 LTC2205-14 BLOCK DIAGRAM AIN+ INPUT S/H FIRST PIPELINED ADC STAGE SECOND PIPELINED ADC STAGE THIRD PIPELINED ADC STAGE FOURTH PIPELINED ADC STAGE FIFTH PIPELINED ADC STAGE GND VDD AIN- DITHER SIGNAL GENERATOR CORRECTION LOGIC AND SHIFT REGISTER RANGE SELECT SENSE PGA VCM ADC REFERENCE ADC CLOCKS OVDD CLKOUT+ CLKOUT- OF CONTROL LOGIC OUTPUT DRIVERS D13 D12 D1 D0 BUFFER VOLTAGE REFERENCE DIFFERENTIAL INPUT LOW JITTER CLOCK DRIVER * * * OGND ENC+ ENC- SHDN PGA RAND M0DE OE DITH 220514 F01 Figure 1. Functional Block Diagram TIMING DIAGRAM tAP ANALOG INPUT N+1 N+3 N+4 N+2 tH tL ENC - N ENC+ tD D0-D13, OF tC N-7 N-6 N-5 N-4 N-3 CLKOUT+ CLKOUT - 220514 TD01 220514fa 13 LTC2205-14 OPERATION DYNAMIC PERFORMANCE Signal-to-Noise Plus Distortion Ratio The signal-to-noise plus distortion ratio [S/(N+D)] is the ratio between the RMS amplitude of the fundamental input frequency and the RMS amplitude of all other frequency components at the ADC output. The output is band limited to frequencies above DC to below half the sampling frequency. Signal-to-Noise Ratio The signal-to-noise (SNR) is the ratio between the RMS amplitude of the fundamental input frequency and the RMS amplitude of all other frequency components, except the first five harmonics. Total Harmonic Distortion Total harmonic distortion is the ratio of the RMS sum of all harmonics of the input signal to the fundamental itself. The out-of-band harmonics alias into the frequency band between DC and half the sampling frequency. THD is expressed as: THD = -20Log by the presence of another sinusoidal input at a different frequency. If two pure sine waves of frequencies fa and fb are applied to the ADC input, nonlinearities in the ADC transfer function can create distortion products at the sum and difference frequencies of mfa nfb, where m and n = 0, 1, 2, 3, etc. For example, the 3rd order IMD terms include (2fa + fb), (fa + 2fb), (2fa - fb) and (fa - 2fb). The 3rd order IMD is defined as the ratio of the RMS value of either input tone to the RMS value of the largest 3rd order IMD product. Spurious Free Dynamic Range (SFDR) The ratio of the RMS input signal amplitude to the RMS value of the peak spurious spectral component expressed in dBc. SFDR may also be calculated relative to full scale and expressed in dBFS. Full Power Bandwidth The Full Power bandwidth is that input frequency at which the amplitude of the reconstructed fundamental is reduced by 3dB for a full scale input signal. Aperture Delay Time / V12 The time from when a rising ENC+ equals the ENC- voltage to the instant that the input signal is held by the sampleand-hold circuit. Aperture Delay Jitter The variation in the aperture delay time from convertion to conversion. This random variation will result in noise when sampling an AC input. The signal to noise ratio due to the jitter alone will be: SNRJITTER = -20log (2 * fIN * tJITTER) (V 2 2 + V3 + V4 + ...VN 2 2 2 ) where V1 is the RMS amplitude of the fundamental frequency and V2 through VN are the amplitudes of the second through nth harmonics. Intermodulation Distortion If the ADC input signal consists of more than one spectral component, the ADC transfer function nonlinearity can produce intermodulation distortion (IMD) in addition to THD. IMD is the change in one sinusoidal input caused 220514fa 14 LTC2205-14 APPLICATIONS INFORMATION CONVERTER OPERATION The LTC2205-14 is a CMOS pipelined multi-step converter with a front-end PGA. As shown in Figure 1, the converter has five pipelined ADC stages; a sampled analog input will result in a digitized value seven cycles later (see the Timing Diagram section). The analog input is differential for improved common mode noise immunity and to maximize the input range. Additionally, the differential input drive will reduce even order harmonics of the sample and hold circuit. The encode input is also differential for improved common mode noise immunity. The LTC2205-14 has two phases of operation, determined by the state of the differential ENC+/ENC- input pins. For brevity, the text will refer to ENC+ greater than ENC- as ENC high and ENC+ less than ENC- as ENC low. Each pipelined stage shown in Figure 1 contains an ADC, a reconstruction DAC and a residue amplifier. In operation, the ADC quantizes the input to the stage, and the quantized value is subtracted from the input by the DAC to produce a residue. The residue is amplified and output by the residue amplifier. Successive stages operate out of phase so that when odd stages are outputting their residue, the even stages are acquiring that residue and vice versa. When ENC is low, the analog input is sampled differentially directly onto the input sample-and-hold capacitors, inside the "input S/H" shown in the block diagram. At the instant that ENC transitions from low to high, the voltage on the sample capacitors is held. While ENC is high, the held input voltage is buffered by the S/H amplifier which drives the first pipelined ADC stage. The first stage acquires the output of the S/H amplifier during the high phase of ENC. When ENC goes back low, the first stage produces its residue which is acquired by the second stage. At the same time, the input S/H goes back to acquiring the analog input. When ENC goes high, the second stage produces its residue which is acquired by the third stage. An identical process is repeated for the third and fourth stages, resulting in a fourth stage residue that is sent to the fifth stage for final evaluation. Each ADC stage following the first has additional range to accommodate flash and amplifier offset errors. Results from all of the ADC stages are digitally delayed such that the results can be properly combined in the correction logic before being sent to the output buffer. SAMPLE/HOLD OPERATION AND INPUT DRIVE Sample/Hold Operation Figure 2 shows an equivalent circuit for the LTC2205-14 CMOS differential sample and hold. The differential analog inputs are sampled directly onto sampling capacitors (CSAMPLE) through NMOS transitors. The capacitors shown attached to each input (CPARASITIC) are the summation of all other capacitance associated with each input. During the sample phase when ENC is low, the NMOS transistors connect the analog inputs to the sampling capacitors which charge to, and track the differential input voltage. When ENC transitions from low to high, the sampled input voltage is held on the sampling capacitors. LTC2005-14 VDD RPARASITIC 3 AIN+ VDD RPARASITIC 3 AIN- CPARASITIC 1.8pF VDD CPARASITIC 1.8pF RON 20 CSAMPLE 4.9pF RON 20 CSAMPLE 4.9pF 1.6V 6k ENC+ ENC- 6k 1.6V 220514 F02 Figure 2. Equivalent Input Circuit 220514fa 15 LTC2205-14 APPLICATIONS INFORMATION During the hold phase when ENC is high, the sampling capacitors are disconnected from the input and the held voltage is passed to the ADC core for processing. As ENC transitions from high to low, the inputs are reconnected to the sampling capacitors to acquire a new sample. Since the sampling capacitors still hold the previous sample, a charging glitch proportional to the change in voltage between samples will be seen at this time. If the change between the last sample and the new sample is small, the charging glitch seen at the input will be small. If the input change is large, such as the change seen with input frequencies near Nyquist, then a larger charging glitch will be seen. Common Mode Bias The ADC sample-and-hold circuit requires differential drive to achieve specified performance. Each input should swing 0.5625V for the 2.25V range (PGA = 0) or 0.375V for the 1.5V range (PGA = 1), around a common mode voltage of 1.25V. The VCM output pin (Pin 2) is designed to provide the common mode bias level. VCM can be tied directly to the center tap of a transformer to set the DC input level or as a reference level to an op amp differential driver circuit. The VCM pin must be bypassed to ground close to the ADC with 2.2F or greater. Input Drive Impedence As with all high performance, high speed ADCs the dynamic performance of the LTC2205-14 can be influenced by the input drive circuitry, particularly the second and third harmonics. Source impedance and input reactance can influence SFDR. At the falling edge of ENC the sample-and-hold circuit will connect the 4.9pF sampling capacitor to the input pin and start the sampling period. The sampling period ends when ENC rises, holding the sampled input on the sampling capacitor. Ideally, the input circuitry should be fast enough to fully charge the sampling capacitor during the sampling period 1/(2FENCODE); however, this is not always possible and the incomplete settling may degrade the SFDR. The sampling glitch has been designed to be as linear as possible to minimize the effects of incomplete settling. For the best performance it is recomended to have a source impedence of 100 or less for each input. The source impedence should be matched for the differential inputs. Poor matching will result in higher even order harmonics, especially the second. INPUT DRIVE CIRCUITS Input Filtering A first order RC lowpass filter at the input of the ADC can serve two functions: limit the noise from input circuitry and provide isolation from ADC S/H switching. The LTC2205-14 has a very broadband S/H circuit, DC to 700MHz; it can be used in a wide range of applications; therefore, it is not possible to provide a single recommended RC filter. Figures 3, 4a and 4b show three examples of input RC filtering at three ranges of input frequencies. In general it is desirable to make the capacitors as large as can be tolerated--this will help suppress random noise as well as noise coupled from the digital circuitry. The LTC2205-14 does not require any input filter to achieve data sheet specifications; however, no filtering will put more stringent noise requirements on the input drive circuitry. Transformer Coupled Circuits Figure 3 shows the LTC2205-14 being driven by an RF transformer with a center-tapped secondary. The secondary center tap is DC biased with VCM, setting the ADC input signal at its optimum DC level. Figure 3 shows a 1:1 turns ratio transformer. Other turns ratios can be used; however, as the turns ratio increases so does the impedance seen by the ADC. Source impedance greater than 50 can reduce the input bandwidth and increase high frequency distortion. A disadvantage of using a transformer is the loss of low frequency response. Most small RF transformers have poor performance at frequencies below 1MHz. 220514fa 16 LTC2205-14 APPLICATIONS INFORMATION Center-tapped transformers provide a convenient means of DC biasing the secondary; however, they often show poor balance at high input frequencies, resulting in large 2nd order harmonics. Figure 4a shows transformer coupling using a transmission line balun transformer. This type of transformer has much better high frequency response and balance than flux coupled center tap transformers. Coupling capacitors are added at the ground and input primary terminals to allow the secondary terminals to be biased at 1.25V. Figure 4b shows the same circuit with components suitable for higher input frequencies. Direct Coupled Circuits Figure 5 demonstrates the use of a differential amplifier to convert a single ended input signal into a differential input signal. The advantage of this method is that it provides low frequency input response; however, the limited gain bandwidth of any op amp or closed-loop amplifier will degrade the ADC SFDR at high input frequencies. Additionally, wideband op amps or differential amplifiers tend to have high noise. As a result, the SNR will be degraded unless the noise bandwidth is limited prior to the ADC input. VCM 2.2F 5 10 T1 8.2pF 35 8.2pF 0.1F 10 T1 = MA/COM ETC1-1T RESISTORS, CAPACITORS ARE 0402 PACKAGE SIZE EXCEPT 2.2F 35 5 AIN- 8.2pF 220514 F03 5 AIN+ LTC2205-14 Figure 3. Single-Ended to Differential Conversion Using a Transformer. Recommended for Input Frequencies from 5MHz to 150MHz VCM 2.2F 0.1mF ANALOG INPUT 25 T1 1:1 25 10 10 0.1F 4.7pF 5 4.7pF 5 AIN+ LTC2205-14 4.7pF 0.1F T1 1:1 0.1F ANALOG INPUT 25 0.1F 2.2F 5 2.2pF AIN+ LTC2205-14 VCM 0.1mF AIN- 220514 F04a 25 5 2.2pF AIN- 22054 F04b T1 = MA/COM ETC1-1-13 RESISTORS, CAPACITORS ARE 0402 PACKAGE SIZE EXCEPT 2.2mF T1 = MA/COM ETC1-1-13 RESISTORS, CAPACITORS ARE 0402 PACKAGE SIZE EXCEPT 2.2F Figure 4a. Using a Transmission Line Balun Transformer. Recommended for Input Frequencies from 150MHz to 250MHz Figure 4b. Using a Transmission Line Balun Transformer. Recommended for Input Frequencies from 250MHz to 500MHz 220514fa 17 LTC2205-14 APPLICATIONS INFORMATION VCM HIGH SPEED DIFFERENTIAL AMPLIFIER ANALOG INPUT 2.2F 25 12pF AIN+ LTC2205-14 TIE TO VDD TO USE INTERNAL 2.5V REFERENCE OR INPUT FOR EXTERNAL 2.5V REFERENCE OR INPUT FOR EXTERNAL 1.25V REFERENCE LTC2205-14 RANGE SELECT AND GAIN CONTROL SENSE PGA INTERNAL ADC REFERENCE + CM + - 25 - AIN- 12pF 220514 F05 AMPLIFIER = LTC6600-20, LTC1993, ETC. 2.5V BANDGAP REFERENCE VCM 2.2F BUFFER 1.25V Figure 5. DC Coupled Input with Differential Amplifier Reference Operation 220514 F06 Figure 6 shows the LTC2205-14 reference circuitry consisting of a 2.5V bandgap reference, a programmable gain amplifier and control circuit. The LTC2205-14 has three modes of reference operation: Internal Reference, 1.25V external reference or 2.5V external reference. To use the internal reference, tie the SENSE pin to VDD. To use an external reference, simply apply either a 1.25V or 2.5V reference voltage to the SENSE input pin. Both 1.25V and 2.5V applied to SENSE will result in a full-scale range of 2.25VP-P (PGA = 0). A 1.25V output, VCM is provided for a common mode bias for input drive circuitry. An external bypass capacitor is required for the VCM output. This provides a high frequency low impedance path to ground for internal and external circuitry. This is also the compensation capacitor for the reference; it will not be stable without this capacitor. The minimum value required for stability is 2.2F. The internal programmable gain amplifier provides the internal reference voltage for the ADC. This amplifier has very stringent settling requirements and is not accessible for external use. Figure 6. Reference Circuit 1.25V VCM 2.2F 3.3V 1F 2 LTC1461-2.5 4 6 SENSE 2.2F LTC2205-14 220514 F07 Figure 7. A 2.25V Range ADC with an External 2.5V Reference The SENSE pin can be driven 5% around the nominal 2.5V or 1.25V external reference inputs. This adjustment range can be used to trim the ADC gain error or other system gain errors. When selecting the internal reference, the SENSE pin should be tied to VDD as close to the converter as possible. If the sense pin is driven externally it should be bypassed to ground as close to the device as possible with 1F (or larger) ceramic capacitor. 220514fa 18 LTC2205-14 APPLICATIONS INFORMATION PGA Pin The PGA pin selects between two gain settings for the ADC front-end. PGA = 0 selects an input range of 2.25VP-P; PGA = 1 selects an input range of 1.5VP-P. The 2.25V input range has the best SNR; however, the distortion will be higher for input frequencies above 100MHz. For applications with high input frequencies, the low input range will have improved distortion; however, the SNR will be worse by up to approximately 2dB. See the Typical Performance Characteristics section. Driving the Encode Inputs The noise performance of the LTC2205-14 can depend on the encode signal quality as much as on the analog input. The encode inputs are intended to be driven differentially, primarily for noise immunity from common mode noise sources. Each input is biased through a 6k resistor to a 1.6V bias. The bias resistors set the DC operating point for transformer coupled drive circuits and can set the logic threshold for single-ended drive circuits. Any noise present on the encode signal will result in additional aperture jitter that will be RMS summed with the inherent ADC aperture jitter. In applications where jitter is critical (high input frequencies), take the following into consideration: 1. Differential drive should be used. 2. Use as large an amplitude possible. If using transformer coupling, use a higher turns ratio to increase the amplitude. 3. If the ADC is clocked with a fixed frequency sinusoidal signal, filter the encode signal to reduce wideband noise. 4. Balance the capacitance and series resistance at both encode inputs such that any coupled noise will appear at both inputs as common mode noise. The encode inputs have a common mode range of 1.2V to 3V. Each input may be driven from ground to VDD for single-ended drive. LTC2205-14 VDD TO INTERNAL ADC CLOCK DRIVERS VDD 1.6V ENC+ 0.1F ENCODE INPUT ETC1-1T 50 100 VDD 1.6V 50 33pF ENC- 6k 6k * * 0.1F 220514 F08 Figure 8. Transformer Driven Encode 220514fa 19 LTC2205-14 APPLICATIONS INFORMATION VTHRESHOLD = 1.6V ENC+ 1.6V ENC- LTC2205-14 0.1F 220514 F09 The lower limit of the LTC2205-14 sample rate is determined by droop of the sample and hold circuits. The pipelined architecture of this ADC relies on storing analog signals on small valued capacitors. Junction leakage will discharge the capacitors. The specified minimum operating frequency for the LTC2205-14 is 1Msps. DIGITAL OUTPUTS Digital Output Buffers Figure 9. Single-Ended ENC Drive, Not Recommended for Low Jitter 3.3V MC100LVELT22 3.3V 130 Q0 130 ENC+ ENC- LTC2205-14 83 83 220514 F10 D0 Q0 Figure 11 shows an equivalent circuit for a single output buffer. Each buffer is powered by OVDD and OGND, isolated from the ADC power and ground. The additional N-channel transistor in the output driver allows operation down to low voltages. The internal resistor in series with the output eliminates the need for external damping resistors. As with all high speed/high resolution converters, the digital output loading can affect the performance. The digital outputs of the LTC2205-14 should drive a minimum capacitive load to avoid possible interaction between the digital outputs and sensitive input circuitry. The output should be buffered with a device such as a ALVCH16373 CMOS latch. For full speed operation the capacitive load should be kept under 10pF. A resistor in series with the output may be used but is not required since the ADC has a series resistor of 33 on chip. Lower OVDD voltages will also help reduce interference from the digital outputs. LTC2205-14 VDD VDD OVDD 0.5V TO 3.6V 0.1F OVDD DATA FROM LATCH PREDRIVER LOGIC 33 TYPICAL DATA OUTPUT OGND Figure 10. ENC Drive Using a CMOS to PECL Translator Maximum and Minimum Encode Rates The maximum encode rate for the LTC2205-14 is 65Msps. For the ADC to operate properly the encode signal should have a 50% (2.5%) duty cycle. Achieving a precise 50% duty cycle is easy with differential sinusoidal drive using a transformer or using symmetric differential logic such as PECL or LVDS. When using a single-ended ENCODE signal asymmetric rise and fall times can result in duty cycles that are far from 50%. An optional clock duty cycle stabilizer can be used if the input clock does not have a 50% duty cycle. This circuit uses the rising edge of ENC pin to sample the analog input. The falling edge of ENC is ignored and an internal falling edge is generated by a phase-locked loop. The input clock duty cycle can vary from 30% to 70% and the clock duty cycle stabilizer will maintain a constant 50% internal duty cycle. If the clock is turned off for a long period of time, the duty cycle stabilizer circuit will require one hundred clock cycles for the PLL to lock onto the input clock. To use the clock duty cycle stabilizer, the MODE pin must be connected to 1/3VDD or 2/3VDD using external resistors. 220514 F11 Figure 11. Equivalent Circuit for a Digital Output Buffer 220514fa 20 LTC2205-14 APPLICATIONS INFORMATION Data Format The LTC2205-14 parallel digital output can be selected for offset binary or 2's complement format. The format is selected with the MODE pin. This pin has a four level logic input, centered at 0, 1/3VDD, 2/3VDD and VDD. An external resistor divider can be user to set the 1/3VDD and 2/3VDD logic levels. Table 1 shows the logic states for the MODE pin. Table 1. MODE Pin Function MODE 0(GND) 1/3VDD 2/3VDD VDD OUTPUT FORMAT Offset Binary Offset Binary 2's Complement 2's Complement CLOCK DUTY CYCLE STABILIZER Off On On Off RAND = HIGH, SCRAMBLE ENABLED D1 D1/D0 D2 LTC2205-14 CLKOUT CLKOUT OF OF D13 D13/D0 D12 D12/D0 * * * D2/D0 Overflow Bit An overflow output bit (OF) indicates when the converter is over-ranged or under-ranged. A logic high on the OF pin indicates an overflow or underflow. Output Clock The ADC has a delayed version of the encode input available as a digital output. Both a noninverted version, CLKOUT+ and an inverted version CLKOUT- are provided. The CLKOUT+/CLKOUT- can be used to synchronize the converter data to the digital system. This is necessary when using a sinusoidal encode. Data can be latched on the rising edge of CLKOUT+ or the falling edge of CLKOUT-. CLKOUT+ falls and CLKOUT- rises as the data outputs are updated. Digital Output Randomizer Interference from the ADC digital outputs is sometimes unavoidable. Interference from the digital outputs may be from capacitive or inductive coupling or coupling through the ground plane. Even a tiny coupling factor can result in discernible unwanted tones in the ADC output spectrum. By randomizing the digital output before it is transmitted off chip, these unwanted tones can be randomized, trading a slight increase in the noise floor for a large reduction in unwanted tone amplitude. RAND D0 220514 F12 D0 Figure 12. Functional Equivalent of Digital Output Randomizer The digital output is "Randomized" by applying an exclusive-OR logic operation between the LSB and all other data output bits. To decode, the reverse operation is applied; that is, an exclusive-OR operation is applied between the LSB and all other bits. The LSB, OF and CLKOUT output are not affected. The output Randomizer function is active when the RAND pin is high. Output Driver Power Separate output power and ground pins allow the output drivers to be isolated from the analog circuitry. The power supply for the digital output buffers, OVDD, should be tied to the same power supply as for the logic being driven. OVDD can be powered with any logic voltage up to the VDD of the ADC. OGND can be powered with any voltage from ground up to 1V and must be less than OVDD. The logic outputs will swing between OGND and OVDD. 220514fa 21 LTC2205-14 APPLICATIONS INFORMATION PC BOARD FPGA CLKOUT Internal Dither The LTC2205-14 is a 14-bit ADC with a very linear transfer function; however, at low input levels even slight imperfections in the transfer function will result in unwanted tones. Small errors in the transfer function are usually a result of ADC element mismatches. An optional internal dither mode can be enabled to randomize the input location on the ADC transfer curve, resulting in improved SFDR for low signal levels. As shown in Figure 14, the output of the sample-and-hold amplifier is summed with the output of a dither DAC. The dither DAC is driven by a long sequence pseudo-random number generator; the random number fed to the dither DAC is also subtracted from the ADC result. If the dither DAC is precisely calibrated to the ADC, very little of the dither signal will be seen at the output. The dither signal that does leak through will appear as white noise. The dither DAC is calibrated to result in less than 0.5dB elevation in the noise floor of the ADC, as compared to the noise floor with dither off. OF D13/D0 D13 D12/D0 D12 LTC2205-14 D2/D0 * * * D2 D1/D0 D1 D0 D0 22054 F13 Figure 13. Descrambling a Scrambled Digital Output LTC2205-14 CLKOUT OF D13 * * * D0 AIN+ ANALOG INPUT AIN- S/H AMP 14-BIT PIPELINED ADC CORE DIGITAL SUMMATION OUTPUT DRIVERS CLOCK/DUTY CYCLE CONTROL PRECISION DAC MULTIBIT DEEP PSEUDO-RANDOM NUMBER GENERATOR 220514 F14 ENC + ENC - DITH DITHER ENABLE HIGH = DITHER ON LOW = DITHER OFF Figure 14. Functional Equivalent Block Diagram of Internal Dither Circuit 220514fa 22 LTC2205-14 APPLICATIONS INFORMATION Grounding and Bypassing The LTC2205-14 requires a printed circuit board with a clean unbroken ground plane; a multilayer board with an internal ground plane is recommended. The pinout of the LTC2205-14 has been optimized for a flowthrough layout so that the interaction between inputs and digital outputs is minimized. Layout for the printed circuit board should ensure that digital and analog signal lines are separated as much as possible. In particular, care should be taken not to run any digital track alongside an analog signal track or underneath the ADC. High quality ceramic bypass capacitors should be used at the VDD, VCM, and OVDD pins. Bypass capacitors must be located as close to the pins as possible. The traces connecting the pins and bypass capacitors must be kept short and should be made as wide as possible. The LTC2205-14 differential inputs should run parallel and close to each other. The input traces should be as short as possible to minimize capacitance and to minimize noise pickup. Heat Transfer Most of the heat generated by the LTC2205-14 is transferred from the die through the bottom-side exposed pad. For good electrical and thermal performance, the exposed pad must be soldered to a large grounded pad on the PC board. It is critical that the exposed pad and all ground pins are connected to a ground plane of sufficient area with as many vias as possible. 220514fa 23 LTC2205-14 APPLICATIONS INFORMATION Ordering Guide: DEMO BOARD NUMBER DC918A-A DC918A-B DC918A-C DC918A-D DC918A-E DC918A-F DC918A-G DC918A-H DC918A-I DC918A-J DC918A-K DC918A-L PART NUMBER LTC2207CUK LTC2207CUK LTC2206CUK LTC2206CUK LTC2205CUK LTC2205CUK LTC2204CUK LTC2207CUK-14 LTC2207CUK-14 LTC2206CUK-14 LTC2206CUK-14 LTC2205CUK-14 RESOLUTION 16-Bit 16-Bit 16-Bit 16-Bit 16-Bit 16-Bit 16-Bit 14-Bit 14-Bit 14-Bit 14-Bit 14-Bit SPEED 105Msps 105Msps 80Msps 80Msps 65Msps 65Msps 40Msps 105Msps 105Msps 80Msps 80Msps 65Msps INPUT FREQUENCY 1MHz to 70MHz 70MHz to 140MHz 1MHz to 70MHz 70MHz to 140MHz 1MHz to 70MHz 70MHz to 140MHz 1MHz to 70MHz 1MHz to 70MHz 70MHz to 140MHz 1MHz to 70MHz 70MHz to 140MHz 1MHz to 70MHz USB I/F BOARD DC718 DC718 DC718 DC718 DC718 DC718 DC718 DC718 DC718 DC718 DC718 DC718 See Web site for ordering details or contact local sales. 220514fa 24 LTC2205-14 APPLICATIONS INFORMATION Silkscreen Top Top Side Inner Layer 2 Inner Layer 3 220514fa 25 LTC2205-14 APPLICATIONS INFORMATION Inner Layer 4 Inner Layer 5 Bottom Side Silkscreen Bottom 220514fa 26 LTC2205-14 PACKAGE DESCRIPTION UK Package 48-Lead Plastic QFN (7mm x 7mm) (Reference LTC DWG # 05-08-1704) 0.70 0.05 5.15 0.05 5.50 REF 6.10 0.05 7.50 0.05 (4 SIDES) 5.15 0.05 PACKAGE OUTLINE 0.25 0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 7.00 0.10 (4 SIDES) 0.75 0.05 R = 0.115 TYP R = 0.10 TYP 47 48 0.40 0.10 1 2 PIN 1 CHAMFER C = 0.35 PIN 1 TOP MARK (SEE NOTE 6) 5.15 0.10 5.50 REF (4-SIDES) 5.15 0.10 0.200 REF 0.00 - 0.05 NOTE: 1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE MO-220 VARIATION (WKKD-2) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE, IF PRESENT 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE (UK48) QFN 0406 REV C 0.25 0.05 0.50 BSC BOTTOM VIEW--EXPOSED PAD 220514fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 27 LTC2205-14 RELATED PARTS PART NUMBER DESCRIPTION LTC1748 LTC1750 LT1993-2 LT1994 LTC2202 LTC2203 LTC2204 LTC2205 LTC2206 LTC2207 LTC2208 LTC2220-1 LTC2224 LTC2255 LTC2284 LT5512 LT5514 LT5515 LT5516 LT5517 LT5522 14-Bit, 80Msps 5V ADC 14-Bit, 80Msps, 5V Wideband ADC High Speed Differential Op Amp Low Noise, Low Distortion Fully Differential Input/ Output Amplifier/Driver 16-Bit, 10Msps, 3.3V ADC, Lowest Noise 16-Bit, 25Msps, 3.3V ADC, Lowest Noise 16-Bit, 40Msps, 3.3V ADC 16-Bit, 65Msps, 3.3V ADC 16-Bit, 80Msps, 3.3V ADC 16-Bit, 105Msps, 3.3V ADC 16-Bit, 130Msps, 3,3V ADC, LVDS Outputs 12-Bit, 185Msps, 3.3V ADC, LVDS Outputs 12-Bit, 135Msps, 3.3V ADC, High IF Sampling 14-Bit, 125Msps, 3V ADC, Lowest Power 14-Bit, Dual, 105Msps, 3V ADC, Low Crosstalk Ultralow Distortion IF Amplifier/ADC Driver with Digitally Controlled Gain 1.5GHz to 2.5GHz Direct Conversion Quadrature Demodulator 800MHz to 1.5GHz Direct Conversion Quadrature Demodulator 40MHz to 900MHz Direct Conversion Quadrature Demodulator 600MHz to 2.7GHz High Linearity Downconverting Mixer COMMENTS 76.3dB SNR, 90dB SFDR, 48-Pin TSSOP Package Up to 500MHz IF Undersampling, 90dB SFDR 800MHz BW, 70dBc Distortion at 70MHz, 6dB Gain Low Distortion: -94dBc at 1MHz 140mW, 81.6dB SNR, 100dB SFDR, 48-pin QFN 220mW, 81.6dB SNR, 100dB SFDR, 48-pin QFN 480mW, 79.1dB SNR, 100dB SFDR, 48-pin QFN 610mW, 79dB SNR, 100dB SFDR, 48-pin QFN 725mW, 77.9dB SNR, 100dB SFDR, 48-pin QFN 900mW, 77.9dB SNR, 100dB SFDR, 48-pin QFN 1250mW, 77.9dB SNR, 100dB SFDR, 64-pin QFN 910mW, 67.7dB SNR, 80dB SFDR, 64-pin QFN 630mW, 67.6dB SNR, 84dB SFDR, 48-pin QFN 395mW, 72.5dB SNR, 88dB SFDR, 32-pin QFN 540mW, 72.4dB SNR, 88dB SFDR, 64-pin QFN 450MHz to 1dB BW, 47dB OIP3, Digital Gain Control 10.5dB to 33dB in 1.5dB/Step High IIP3: 20dBm at 1.9GHz, Integrated LO Quadrature Generator High IIP3: 21.5dBm at 900MHz, Integrated LO Quadrature Generator High IIP3: 21dBm at 800MHz, Integrated LO Quadrature Generator 4.5V to 5.25V Supply, 25dBm IIP3 at 900MHz. NF = 12.5dB, 50W Single Ended RF and LO Ports DC-3GHz High Signal Level Downconverting Mixer DC to 3GHz, 21dBm IIP3, Integrated LO Buffer 220514fa 28 Linear Technology Corporation (408) 432-1900 LT 0506 REV A * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2006 |
Price & Availability of LTC2205-14 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |